WARNING: we strongly suggest having a professional look at any appliance before trying to repair on your own, We are not liable for any accidents or damage to your appliance or yourself please exercise extreme caution on any appliance, electric shock can be fatal.

Save time and money with our professional factory trained technicians. We get the job quickly and correctly. Professional and factory trained technicians assures the customer the repair is done right with quality parts. This will prevent the need for future appliance repair needs. Schedule your appliance repair issues with your washer and dryer today by setting up an appointment with us today online or giving us a call. We can repair all major washer and dryer brands. We service Idaho Falls, Shelley, Rigby, Ririe, Ucon, and surrounding areas.

 

We at Expert Appliance Repair and Service can help get your washer and Dryer back into operation quickly and reliably. Our washer repairs come with a one year warranty so you can rest easy knowing you are getting the best service around. We service Idaho Falls, Shelley, Rigby, and surrounding areas.

Does not power up at all.

  1. No power to the washer

    Make sure there's power getting to the washer. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the washer, if this is the case, the wiring must be repaired or replaced.

  2. Lid switch

    The washing machine may not function if the lid switch is defective. The switch is usually located near the door. Replace if found defective.

It fills and drains at the same time

  1. Drain hose

    The drain hose might be too low. Make sure the drain hose is at least three feet above the floor.

  2. Clogged drain line or water pump

    Check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine).

  3. Water Pump

    If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Note: if you have a belt driven washer, check the belt(s) for cracks, as this would be a perfect time to replace the belt(s) if needed.

It doesn’t drain

  1. Lid switch assembly

    If the washer will not drain a very common issue is that the lid switch assembly has malfunctioned. The lid switch can fail either mechanically or electrically and should be tested with an ohm meter for continuity. If the part has failed it will need to be replaced.

  2. Drain pump or hose

    If the lid switch assembly is functioning, the next thing to check for is a clogged pump or hose. Small clothing (especially baby clothing or socks) can get sucked into the drain system and clog the hose that leads to the pump, or even the pump itself. You can also check to see if there is a kink in the hose and check the functionality of the drain pump. When removing the hoses to check for obstructions, keep in mind that any water remaining in the washer will flow out when the hoses are removed. Therefore it is good to have towels prepared in case this happens.

  3. Water pump belt

    If there is no obstruction in the pump or hose, the next thing to check is the water pump belt. These belts wear out and break over time, and will need to be replaced if broken or showing excessive wear.

  4. Drive belt

    If the washer is still not draining, the next thing to check is the drive belt. If this belt is worn, broken, or not on the pulley system, the washer will possibly not drain at all. If the belt has excessive wear or is broken it will need to be replaced.

  5. Coin trap

    If the washer is not draining and everything is functioning, the final thing to check is the coin trap. This device is located near the water pump and it catches any foreign materials that make their way down the drain. This part often has an access panel and can normally be cleaned very easily.

No hot water

Make sure the hot water is turned on.

No cold water

Make sure the cold water is turned on.

There is no water at all

First, make sure there's water getting to the washing machine.
 

  1. Water Inlet Valve

    Replace if found defective.

WASHER REPAIR TROUBLSHOOTING

Idaho Falls

Shelley

 

Rigby

More areas to come

This site was designed with the
.com
website builder. Create your website today.
Start Now